Toyota Rav4 2017 Headlight Bulb Blown Out Again

Toyota RAV4 Owners Manual: Calorie-free bulbs

Yous may replace the following bulbs by yourself. The difficulty level of replacement varies depending on the bulb. If necessary bulb replacement seems difficult to perform, contact your toyota dealer.

For more information about replacing other light bulbs, contact your toyota dealer.

Preparing for light seedling replacement

Check the wattage of the low-cal seedling to be replaced.

Seedling locations

Front

1. Headlight depression beam
2. Daytime running light/headlight high axle
3. Front turn bespeak light/parking light
4. Front side marker low-cal
5. Fog light (if equipped)

Rear

1. Tail light
2. Back-up calorie-free
3. Rear turn signal lite
4. Terminate/tail light and rear side marker light
5. License plate lights

Replacing low-cal bulbs

Headlight depression beams

1. For the right side only: remove the securing clip.

   Then movement the washer tank inlet.

2. Disconnect the connector and turn the cover counterclockwise.

3. Unplug the connector while pulling the lock release.

4. Turn the bulb base counterclockwise.

5. Set the new light bulb.

Marshal the iii tabs on the light seedling with the mounting, and insert.

Turn it clockwise to set up.

6. Set the connector.

After installing the connector, shake the bulb base of operations gently to bank check that it is not loose.

7. Fix the connector and install the cover.

Before installing the cover, turn the headlight low beams on one time and visually confirm that no light is leaking through the mounting.

8. For the correct side only: move the washer tank inlet and install the securing clip.

Daytime running lights/headlight loftier beams

1. For the right side only: remove the securing clip. Then motility the washer tank inlet.
2. Plough the bulb base counterclockwise.

3. Unplug the connector while pressing the lock release.

4. Supercede the light bulb, and install the seedling base of operations.

Align the 3 tabs on the light bulb with the mounting, and insert.

5. Turn and secure the bulb base of operations.

Shake the seedling base gently to check that it is non loose, plow the headlights on once and visually confirm that no low-cal is leaking through the mounting.

6. For the correct side merely: motility the washer tank inlet and install the securing prune.

Front turn signal lights/parking lights

1. Plough the bulb base counterclockwise.

2. Remove the light bulb.

3. When installing, reverse the steps listed.

Front side maker lights

1. Plow the seedling base counterclockwise.

2. Remove the light seedling.

3. When installing, reverse the steps listed.

Fog lights (if equipped)

1. To permit enough working space, plough the steering wheel to the reverse side of the bulb to be replaced.

Plow the steering wheel to the left when replacing the correct side lite bulb, and turn the steering wheel to the correct when replacing the left side light bulb.

2. Remove the fender liner clip and open up the fender liner.

3. Unplug the connector while pressing the lock release.

4. Plow the bulb base of operations counterclockwise.

5. Set the new light bulb.

   Align the three tabs on the light bulb with the mounting, and insert.

   Turn it clockwise to set up.

6. Set the connector.

   After installing the connector, shake the seedling base gently to check that information technology is not loose, turn the fog lights on once and visually ostend that no light is leaking through the mounting.

7. Reinstall the fender liner and install the prune.

   Insert the clip and turn to lock.

Terminate/tail lights and rear side mark lights, and rear turn indicate lights

1. Open the dorsum door and remove the bolts, and remove the lamp associates by pulling it directly backward from the rear of the vehicle.

2. Turn the bulb base counterclockwise.

Stop/tail lights and rear side marker lights

Rear turn signal lights

3. Remove the calorie-free bulb.

Terminate/tail lights and rear side mark lights

Rear plow bespeak lights

4. When installing, reverse the steps listed.

Tail lights and back-up lights

1. Open up the back door and remove the cover.

To prevent damage, cover the tip of the screwdriver with rag.

2. Turn the bulb base counterclockwise.

Tail lights

Dorsum-up lights

3. Remove the light bulb.

Tail lights

Back-up lights

4. When installing, reverse the steps listed.

License plate lights

1. Open the back door and remove the embrace.

To prevent impairment, embrace the tip of the screwdriver with rag.

2. Turn the bulb base of operations counterclockwise.

Left side

Right side

3. Remove the low-cal bulb.

4. When installing, reverse the steps listed.

If any of the lights listed beneath has burnt out, take it replaced by your toyota dealer.

• Side plow signal lights (if equipped)
• High mounted stoplight

Afterwards moving the washer tank inlet

Subsequently replacing the bulbs, return the washer tank inlet to its original position with the prune.

1. Insert
2. Press

Led lights

The side plow signal lights (if equipped) and high mounted stoplight consist of a number of leds. If whatsoever of the leds burn out, take your vehicle to your toyota dealer to have the lite replaced.

Condensation build-upwards on the within of the lens

Temporary condensation build-up on the inside of the headlight lens does non bespeak a malfunction.

Contact your toyota dealer for more than information in the following situations:

• Large drops of water have built up on the inside of the lens.
• H2o has built up inside the headlight.

Caution

Replacing calorie-free bulbs

• Plow off the lights. Do not attempt to supplant the bulb immediately after turning off the lights.

  The bulbs become very hot and may cause burns.

• Do not touch the drinking glass portion of the light bulb with bare hands. When it is unavoidable to hold the glass portion, use and hold with a clean dry out textile to avoid getting moisture and oils on the seedling.

  Likewise, if the seedling is scratched or dropped, it may blow out or crack.

• Fully install light bulbs and whatsoever parts used to secure them. Failure to do so may result in heat impairment, fire, or water entering the headlight unit. This may damage the headlights or cause condensation to build up on the lens.
• Do not attempt to repair or detach low-cal bulbs, connectors, electric circuits or component parts.

  Doing so may result in death or serious injury due to electric shock.

To preclude damage or fire

• Brand sure bulbs are fully seated and locked.
• Check the wattage of the bulb before installing to prevent heat harm.

Checking and replacing fuses

If any of the electrical components practice not operate, a fuse may have blown. If this happens, check and replace the fuses as necessary. Vehicles without a smart key system: turn the engine switch ...

Other materials:

How to proceed with troubleshooting
Hint: Use these procedures to troubleshoot the lighting system. *: Use the intelligent tester. Vehicle brought to workshop Inspect battery voltage Standard voltage: xi to 14 5 If the voltage is below 11 v, recharge or replace the battery before proceeding. Refer to pr ...

Abs alert lite does not come on
Wiring diagram Refer to the abs warning light excursion (see page bc-135). Inspection process Check can communication system Cheque if the can communication system dtc is output (encounter page ca-34). Effect Perform active test by intelligent tester (abs warning lite) Sele ...

Curt in front passenger side squib 2nd footstep circuit
Description The front passenger side squib second pace excursion consists of the center airbag sensor and the front passenger airbag. The circuit instructs the srs to deploy when the deployment conditions are met. These dtcs are recorded when a malfunction is detected in the forepart rider ...

herringbelive.blogspot.com

Source: https://www.trav4.net/light_bulbs-228.html